厚松散层薄基岩坚硬顶板工作面覆岩破坏电法监测

掌握导水裂缝带发育高度对于厚松散层薄基岩煤矿工作面安全开采具有重要的意义。在煤层采动影响前,在工作面巷道向煤层工作面顶板施工1个仰孔,布置孔中电极电缆,形成钻孔电法监测系统。在巷道中连接并行电法仪器和钻孔电缆,数据采集方式称为AM法。随采煤工作面位置逐渐接近并进入钻孔控制范围,监测电极电流值和视电阻率值发生变化。结果表明:对潘北煤矿厚松散层薄基岩坚硬顶板工作面电法监测显示,弯曲下沉带电极电流值和视电阻率值较为稳定,受采动影响程度较小;导水裂缝带内,电极电流值明显下降,视电阻率值明显升高;顶板高度0~40 m采动超前影响范围可达410 m左右;工作面坚硬顶板砂岩地层为控制覆岩破坏的关键层,采空区上方坚硬顶板岩层垮落滞后工作面9~16 m;工作面导水裂缝带高度为37 m,导水裂缝带未发育到基岩面,风化砂质泥岩裂隙在采动应力作用下存在闭合现象。     

基于稳定固溶体团簇模型的无扩散阻挡Cu合金薄膜的成分设计

随着超大规模集成电路的发展,器件特征尺寸不断缩小,必然会出现Cu互连扩散阻挡层厚度无法进一步减小等瓶颈问题。因此,开发新型无扩散阻挡层Cu合金薄膜(Cu种籽层)势在必行。该新型互连结构在长时间的中高温(400~500℃)后续工艺实施过程中,需同时具备高的稳定性(不发生互扩散反应)和低的电阻率。基于此,首先综述了目前无扩散阻挡层结构的研究现状及问题,然后对基于稳定固溶体团簇模型设计制备的无扩散阻挡Cu-Ni-M薄膜的研究工作进行了梳理,通过多系列薄膜微观结构、电阻率及稳定性的对比,深入探讨了第三组元M的选择原则及其对薄膜热稳定性的影响。为进一步验证稳定固溶体团簇模型的有效性,对第二组元的变化进行了相关讨论。结果证实,选取原子半径略大于Cu、难扩散且难溶的元素作为第三组元M,薄膜表现出良好的扩散阻挡能力;当M/Ni=1/12,即合金元素完全以团簇形式固溶于Cu基体时,薄膜综合性能达到最优,能够满足微电子行业的要求。所有研究表明,稳定固溶体团簇模型在无扩散阻挡层Cu合金薄膜的成分设计方面十分有效,该模型也有望在耐高温Cu合金及抗辐照材料成分设计方面推广使用。     

Enhanced mechanical and electrical properties of carbon fiber/poly(ether ether ketone) laminates via inserting carbon nanotubes interleaves

The carbon fiber/(carbon nanotubes/polyetherimide)/poly ether ether ketone (CF/(CNTs/PEI)/PEEK) laminates are prepared by inserting carbon nanotubes/polyetherimide (CNTs/PEI) interleaves into interlaminar region. The mechanical properties and electrical conductivities of the developed laminates are evaluated. The results indicate that the interlaminar shear strength and flexural strength of CF/(CNTs/PEI)/PEEK laminates are increased by 42.9% and 24.7%, after inserting CNTs2.91/PEI interleaves, respectively. The cross-sectional images of laminates after mechanical tests verify strong fiber-resin adhesion by scanning electron microscope observation. The pertinent mechanism responsible for the improvement of mechanical properties is mechanical interlocking effect of CNTs. After incorporating CNTs/PEI interleaves, the electrical conductivity of laminates is markedly improved due to the formation of conductive pathway. This work suggests that this method is compatible with the preparation process of thermoplastic composites. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 137, 48658.     

Polytetrafluorethylene-based high-k composites with low dielectric loss filled with priderite (K1.46Ti7.2Fe0.8O16)

Composite materials with a high permittivity (high-k) and low dielectric loss represent an important research direction for the rapid development of modern electronic. This article is about high-k composite with low dielectric loss (dielectric constant is approximately 11, and dielectric loss is only 0.02 at 1 MHz and about 50 wt % of filler) based on a polytetrafluorethylene (PTFE) compounded with priderite (K_1.46Ti_7.2Fe_0.8O₁₆). The dielectric permittivity about ε' ≈ 10³ and the dielectric loss of tgδ ≈ 2 have been found for filler content about 50 wt % (30 vol %) and, respectively, ε' ≈ 11 and tgδ ≈ 0.02 for 1 MHz. To produce filler, amorphous potassium polytitanate was synthesized by molten salt method, modified in aqueous solution of iron sulfate, crystallized at 700 °C and further treated in the aqueous dispersion of PTFE. The obtained product was pressured, dried and investigated by X-ray diffraction and scanning electron microscopy. Dielectric properties of the composite with different ceramic filler content (1–90 wt %) were studied using impedance spectroscopy in the frequency range of 10⁻² to 10⁶ Hz. The influence of frequency on electric conductivity, permittivity, and dielectric losses was analyzed taking into account the experimental data on porosity, apparent density obtained for the composites. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48762.     

Fe/Si比对稀土处理工业纯铝组织性能的影响

通过添加Si改变稀土处理工业纯铝的Fe/Si比,采用金相显微镜、扫描电镜、电子探针、室温拉伸试验和电导率测试研究了Fe/Si比对稀土处理工业纯铝显微组织、屈服强度以及导电率的影响。结果表明: 随着Fe/Si比增大,铸态合金的屈服强度总体呈下降趋势,导电率逐渐上升; 当Fe/Si比不大于1.00时,晶粒尺寸较小,合金强度较高,导电率较低; 当Fe/Si比大于1.00时,晶粒粗大,合金强度降低,导电率提高; Fe元素主要在晶界和晶内第二相中聚集分布,Si元素呈点状均匀分布,稀土元素容易在第二相上聚集。根据Fe/Si比-强度-导电率性能曲线,可通过添加Si改变工业纯铝的Fe/Si比,实现铝材屈服强度、导电率的良好匹配。     

Hydrogen from solar energy,a clean energy carrier from a sustainable source of energy

Solar energy is going to play a crucial role in the future energy scenario of the world that conducts interests to solar-to-hydrogen as a means of achieving a clean energy carrier. Hydrogen is a sustainable energy carrier, capable of substituting fossil fuels and decreasing carbon dioxide (CO₂) emission to save the world from global warming. Hydrogen production from ubiquitous sustainable solar energy and an abundantly available water is an environmentally friendly solution for globally increasing energy demands and ensures long-term energy security. Among various solar hydrogen production routes, this study concentrates on solar thermolysis, solar thermal hydrogen via electrolysis, thermochemical water splitting, fossil fuels decarbonization, and photovoltaic-based hydrogen production with special focus on the concentrated photovoltaic (CPV) system. Energy management and thermodynamic analysis of CPV-based hydrogen production as the near-term sustainable option are developed. The capability of three electrolysis systems including alkaline water electrolysis (AWE), polymer electrolyte membrane electrolysis, and solid oxide electrolysis for coupling to solar systems for H₂ production is discussed. Since the cost of solar hydrogen has a very large range because of the various employed technologies, the challenges, pros and cons of the different methods, and the commercialization processes are also noticed. Among three electrolysis technologies considered for postulated solar hydrogen economy, AWE is found the most mature to integrate with the CPV system. Although substantial progresses have been made in solar hydrogen production technologies, the review indicates that these systems require further maturation to emulate the produced grid-based hydrogen.     

Investigation of fluidized bed behaviour using electrical capacitance tomography

The temporal and cross-sectional distributions of particles in a 127 mm diameter fluidized bed have been obtained using a new generation, high-speed electrical capacitance tomography. Two planes of eight electrodes were used and mounted at 160 and 660 mm from the gas distributor which was a 3 mm thick porous plastic plate (maximum pore size of 50-70 μ m). 3 mm diameter, nearly-spherical polyethylene granules made up the bed. Experiments at sampling frequencies of 200-2000 cross-sections per second and gas superficial velocities from just below the minimum fluidization to 83% above minimum fluidization velocities were used. The time series of the cross-sectional average void fractions have been examined both directly and in amplitude and frequency space. The last two used probability density functions and power spectral densities. The information gathered shows that the fluidized bed was operating in the slugging mode, which is not surprising given the size of the particles. It has been found that an increase in the excess gas velocity above the minimum fluidization velocity resulted in an increase in the mean void fraction, an increase in the length and velocity of the slug bubbles as well as the bed height, and a slight decrease in the slug frequency. The results are presented in a level of detail suitable for comparison with later numerical simulation.     

Applicability of electrical resistance tomography to the analysis of fluid distribution in haemodialysis modules

This work aims to explore the applicability of electrical resistance tomography (ERT) in the analysis of fluid distribution in haemodialysis modules, which is not straightforward due to the complex geometry of the hollow fibre bundles and the small sizes of the modules. On the other hand, ERT is potentially a suitable and convenient technique for investigation in this field due to its cost-effectiveness and capacity to perform measurements in opaque systems. After a preliminary estimation of the fibre bundle local distribution, the assessment of the technique is performed by observing the time evolution of the measured conductivity maps during the module filling and emptying operations with water and air, which are alternatively fed inside or outside the fibre bundle. Reliable conductivity maps are obtained by placing the module vertically or horizontally. Additional experimental data collected by feeding liquid mixtures of different sodium chloride concentrations show that the technique is suitable for detecting concentration variations, due to the mass transfer through the fibres, and flow maldistribution, due to the specific geometry of the module. From the preliminary results collected in this work, the technique appears to be adequate for the collection of data that can support the optimization of the module geometry and computational model validation.     

Numerical investigation of thermal and electrical management during hydrogen reversible solid-state storage using a novel heat exchanger based on thermoelectric modules

In order to reduce the costs generated by the hydrogen solid storage tank's accessories such as the heat exchanger, this work was carried out. It shows thermal and electrical investigations of transient hydrogen (H₂) solid storage in a tank filled with porous medium (LaNi₅) to activate a potential PEM automotive fuel cell. For this purpose, we use a novel heat exchanger with a heat sink combined with thermoelectric modules (TEMs). We realize a simulation that helps us verify if thermoelectric exchanger will be an alternative to the conventional ones. The main results are that a thermoelectric cooler and heater with 127 couples of semiconductors coupled with 19 fins heat sink could be used during the reversible hydrogen solid storage. Also, results show that we can avoid the water freezing at negative temperatures when using a conventional heat exchanger by using TEM during hydrogen absorption. Finally, during the endothermic desorption of the hydrogen, TEG use can avoid boiling water used in the heating system. Also, the hydrogen tank will be lighter and compact without fins and water tubes.     

A review on ultrasonic spot welding of copper alloys

As a solid state joining process, ultrasonic spot welding has been proven to be a promising technique for joining copper alloys. However, challenges still remain in employing ultrasonic spot welding to join copper alloys. This article comprehensively reviews the current state of ultrasonic spot welding of copper alloys with a number of critical issues including materials flow, plastic deformation, temperature distribution, vibration, relative motion, vertical displacement, interface friction coefficient, online monitoring technique, coupled with the macrostructure and microstructure, the mechanical properties and electrical conductivity. In addition, the future trends in this field are provided.